#61

Member
gone to Carolina in my mind
(This post was last modified: 04-28-2022, 06:35 AM by HighSpeed.)
(04-25-2022, 04:37 PM)Stubble Daddy Wrote: Well, I just joined the Vector club. Hope to have it in hand later this week!
Well then, I think I'm in some pretty good company.  I also bought a vector this week.  Through the kindness of two fine friends, I've already test driven both models - titanium and stainless.  My overriding conclusion:  They are both astoundingly superb razors.  My secondary conclusion:  The tradeoffs are pretty much as described by Shane in this article (which was brought to my attention by MaineYooper - thank you Eric).  Long story short:  I went with the stainless, which I think is somewhat better for me, but I am open to the possibility of titanium later.

Stubble Daddy, MaineYooper and Dave in KY like this post
Technique Trumps Tools
Skin Care Trumps Skin Repair

Be Cool, be Kind, and be Well
--  Mike --
#62
My new pack of Proline blades that just came don't fit my Vector unfortunately. The last pack fit fine. Is there any option to make them workable? I'd hate to try to Dremel them, but I don't use Artist Club straights and have no other AC safety razors, so I have no real use for them.
#63

Just Here for the Shaves
Williamsburg, KY
(05-02-2022, 02:14 PM)Mtt02263 Wrote: My new pack of Proline blades that just came don't fit my Vector unfortunately. The last pack fit fine. Is there any option to make them workable? I'd hate to try to Dremel them, but I don't use Artist Club straights and have no other AC safety razors, so I have no real use for them.

Have you compared the new prolines to the old ones to see what's different?

MaineYooper likes this post
This post by Dave in KY mentions views and opinions expressed and makes it known that they are "those of the author and do not necessarily reflect the official policy or position of DFS or any other member, agency, organization, employer or company."  Big Grin
#64

Trotter Handcrafts
Bellingham, Washington USA
I've been using my "new-to-me" Vector for the last week. Absolutely love it. Wish I had purchased one a long time ago. Outstanding work Blackland Razors

Marhos24, Blackland Razors, MaineYooper and 1 others like this post
#65

Merchant
San Diego CA
(05-02-2022, 02:14 PM)Mtt02263 Wrote: My new pack of Proline blades that just came don't fit my Vector unfortunately. The last pack fit fine. Is there any option to make them workable? I'd hate to try to Dremel them, but I don't use Artist Club straights and have no other AC safety razors, so I have no real use for them.

Unfortunately, Schicks use a slightly different hole pattern so we no longer consider them to be Vector-compatible. Sometimes they fit okay, but often they do not. You could certainly Dremel them out. Or, if you're really committed to these blades, you could lightly sand the outside surface of the top cap blade pins to make them a few tenths of a mm narrower. The downside to this is that other blades wouldn't have perfect lateral alignment, but that's not a big deal.

(05-02-2022, 04:43 PM)Stubble Daddy Wrote: I've been using my "new-to-me" Vector for the last week. Absolutely love it. Wish I had purchased one a long time ago. Outstanding work Blackland Razors

Awesome! Glad to hear it! <3

Stubble Daddy likes this post
#66

Scentsless Shaver
Oakland, ME
(04-25-2022, 04:37 PM)Stubble Daddy Wrote: Well, I just joined the Vector club. Hope to have it in hand later this week!

[Image: 3TFl3sS.png]

Stubble Daddy likes this post
- Eric 
Put your message in a modem, 
And throw it in the Cyber Sea
--Rush, "Virtuality"

Overloader of brushes, Overlander fanboy, Schickhead, and a GEM in the rough!
#67
(This post was last modified: 05-27-2022, 09:20 PM by Oasisdave.)
Very disappointing to hear about the Schick Proline as it is far and away my favorite. Haven't really liked any of the Feather or Kai I've tried at all.
Dave
"Always walk where you like your steps"
#68

Just Here for the Shaves
Williamsburg, KY
(05-27-2022, 05:48 PM)Oasisdave Wrote: Very disappointing to hear about the Schick ProGuard as it is far and away my favorite. Haven't really liked any of the Feather or Kai I've tried at all.

Schick Proline I think you meant. ProGuard is a Feather product Happy2
This post by Dave in KY mentions views and opinions expressed and makes it known that they are "those of the author and do not necessarily reflect the official policy or position of DFS or any other member, agency, organization, employer or company."  Big Grin
#69

Merchant
San Diego CA
(05-27-2022, 05:48 PM)Oasisdave Wrote: Very disappointing to hear about the Schick ProGuard as it is far and away my favorite. Haven't really liked any of the Feather or Kai I've tried at all.

They usually work, but not always. If one is committed to the Schicks, you can also just take a fine file or a small bit of sandpaper and bring down the outside of the blade posts by a fraction of a mm to get them to fit.
#70
(This post was last modified: 05-27-2022, 09:22 PM by Oasisdave.)
(05-27-2022, 06:21 PM)Dave in KY Wrote:
(05-27-2022, 05:48 PM)Oasisdave Wrote: Very disappointing to hear about the Schick ProGuard as it is far and away my favorite. Haven't really liked any of the Feather or Kai I've tried at all.

Schick Proline I think you meant. ProGuard is a Feather product  Happy2

That would be it, yes   Shy

MaineYooper and Dave in KY like this post
Dave
"Always walk where you like your steps"


Users browsing this thread: 1 Guest(s)