#1
What is your favorite SE razor.  Mine is  Atelier Durdan La Faulx and Mongoose SE

jesseix and DanLaw like this post
#2
Valet Auto Strop:

[Image: wDR7sTf.jpeg]
[Image: yXnym8Q.jpeg]

One of  the few open comb SE razors readily  available.

DanLaw likes this post
#3

Scentsless Shaver
Oakland, ME
I am going to try and pick one for each of the SE blades that I use.

For the GEM, I will go with my Damaskeene.

For the AC-style, the Occam's Razor SE-noch

And for injector blades, the Schick Type I Hydro-magic.

GoodShave, rocket, ewk and 3 others like this post
- Eric 
Put your message in a modem, 
And throw it in the Cyber Sea
--Rush, "Virtuality"

Overloader of brushes, Overlander fanboy, Schickhead, and a GEM in the rough!
#4

intermediate human
NJ
(This post was last modified: 11-15-2024, 06:42 PM by steelwindmachine. Edited 1 time in total.)
vintage Schick L and I. They've mostly put to pasture every other non-Schick type razor I've owned (straights, DE, other SEs) and still own (Yaqi Slope).

I enjoy the lightweight feeling in hand and on the face, the extremely long lasting sharp blades - I'll get somewhere around 15-20 shaves out of a blade before it shows any slight signs of diminished performance. The simplicity mitigates the need to figure out plate/cap/blade combinations.

While not a deciding factor for me, they were gifted to me by another forum's member. They're plentiful and cheap.

MaineYooper, DanLaw, Tedolph and 2 others like this post
#5

Posting Freak
Peachtree City, GA
Hands down Vector Ti

AlphaFrank75, ALI, AlanH81 and 2 others like this post
#6

Member
Quebec, Canada
(This post was last modified: 10-21-2024, 12:18 AM by fblais. Edited 1 time in total.)
(10-06-2024, 03:12 AM)MaineYooper Wrote: For the GEM, I will go with my Damaskeene.

Maybe naive question, but is it possible to use regular GEM blades with a Damaskeene razor?
Thanks in advance!

Tedolph, GoodShave and MaineYooper like this post
--
Ce message provient du Québec!  Happy2
#7
Vector
#8

Member
Gatineau, QC, Canada
Paradigm Se  Happy2


[Image: LfzSAu0.jpeg]

Sascoman, Cino and Tedolph like this post
"Strive not to be a success, but rather to be of value."

  - Albert Einstein
#9
(This post was last modified: 10-21-2024, 03:05 AM by GoodShave. Edited 1 time in total.)
(10-21-2024, 12:17 AM)fblais Wrote:
(10-06-2024, 03:12 AM)MaineYooper Wrote: For the GEM, I will go with my Damaskeene.

Maybe naive question, but is it possible to use regular GEM blades with a Damaskeene razor?
Thanks in advance!

Yes you can. That is all I use with my Damaskeene.
Sometimes I use a half spine shim (a modern spine split in two halves and use one of the halves) taped to the blade on one lower side to equal to the thickness of the vintage GEM blade spine. This raises the blade angle a tiny amount that makes a difference in some vintage ASR razors (at least the ones that pre-date bumps that were added for the GEM double edge blades).

MaineYooper and fblais like this post
#10

Scentsless Shaver
Oakland, ME
(10-21-2024, 12:17 AM)fblais Wrote:
(10-06-2024, 03:12 AM)MaineYooper Wrote: For the GEM, I will go with my Damaskeene.

Maybe naive question, but is it possible to use regular GEM blades with a Damaskeene razor?
Thanks in advance!

GoodShave is correct. I only use the Personna GEM PTFE blades. They have recently been rebranded, so do some digging in the forums to find the correct product. I will try to post it here if I can remember by tomorrow!

fblais and GoodShave like this post
- Eric 
Put your message in a modem, 
And throw it in the Cyber Sea
--Rush, "Virtuality"

Overloader of brushes, Overlander fanboy, Schickhead, and a GEM in the rough!


Users browsing this thread: 1 Guest(s)