#1

Member
Lizard Acres, Arizona - U.S.A.
Keep look at this notifies Razor in Brass n Stainless with Mild plate.

Know company is advertiser, but in searching for info on Forum many have been sold off.

Anyone own this Razor, care to share your experience how it shave, good or bad quality machine, over all satisfaction

metal_shavings likes this post
#2

It's sharp and it cuts. I like it...
Northeast, USA
I know your an information seeker so, here’s a decent thread to give you all the details you need.

https://damnfineshave.com/thread-carbon-...on%2BRazor

Stickshift and metal_shavings like this post
#3

Member
Lizard Acres, Arizona - U.S.A.
Thanks will read tonight.

metal_shavings likes this post
#4

Member
Lizard Acres, Arizona - U.S.A.
(This post was last modified: 10-22-2024, 02:32 AM by DesertIguana. Edited 1 time in total.)
(10-21-2024, 05:53 PM)GlazedBoker Wrote: I know your an information seeker so, here’s a decent thread to give you all the details you need.

https://damnfineshave.com/thread-carbon-...on%2BRazor

Read most seem to like, so not so much.

Plus I am seeking Feedback on Brass, any Brass Owners?
#5

Member
Chester County, PA
(This post was last modified: 10-25-2024, 06:34 PM by dtownvino. Edited 2 times in total.)
It’s a good razor but it has a lot of blade feel and clamping could be improved to remove chatter.  

I’ve owned every plate, mostly Ti and Copper.  No brass experience, but with copper I felt it was more aggressive and a bit too heavy for the original plate.  

If SS, Brass, Copper I would only consider the -, + or ++ plates.

Ask Sean (owner) any questions - great guy!

CarbonShavingCo. likes this post
#6
I bought the Carbon ++ after I tried it during the pass around.  I experienced a close shave, but I found it to be a little aggressive, leaving me with occasional nicks and cuts.  About 6 weeks ago I decided to give it a more thorough test.  It took me several weeks, but I learned to adjust my shaving technique and I'm getting some really good shaves.  My curiosity pushed me to order the + and original plates.  I've found the ++ plate gives me a really good shave, and the + plate is even better (smoother with about the same closeness).  My closeness test is feeling my face for stubble after about 12 hours.  I've found the + plate seems less aggressive than the ++ plate with equal or better results.  Maybe you could say the + plate is more efficient (for me) than the ++ plate.  I'll continue with the + plate for another week or two and then try the original plate.

dtownvino, HOLYZEUS and CarbonShavingCo. like this post
#7

Member
Lizard Acres, Arizona - U.S.A.
Well I am not so sure I want a Carbon, they seem to change owner often.

Still thinking about a Brass with .71 Plate.
#8

Living on the edge
(10-25-2024, 09:26 PM)DesertIguana Wrote: Well I am not so sure I want a Carbon, they seem to change owner often.

Where are you getting this information from?
#9

Member
Lizard Acres, Arizona - U.S.A.
(10-26-2024, 06:54 AM)Tester28 Wrote:
(10-25-2024, 09:26 PM)DesertIguana Wrote: Well I am not so sure I want a Carbon, they seem to change owner often.

Where are you getting this information from?

Assume you talking about observation about the CX Flipping or changing hand frequently. 

Simple search function on couple of Wet Shave Forums, show those results, many people selling CX’s, it appears they were purchase, used, maybe dislike, and sold off.
#10

Just Here for the Shaves
Williamsburg, KY
(10-26-2024, 12:44 PM)DesertIguana Wrote:
(10-26-2024, 06:54 AM)Tester28 Wrote:
(10-25-2024, 09:26 PM)DesertIguana Wrote: Well I am not so sure I want a Carbon, they seem to change owner often.

Where are you getting this information from?

Assume you talking about observation about the CX Flipping or changing hand frequently. 

Simple search function on couple of Wet Shave Forums, show those results, many people selling CX’s, it appears they were purchase, used, maybe dislike, and sold off.
It sounded like you meant the Company changed owners is probably what he thought Happy2

jags009 likes this post
This post by Dave in KY mentions views and opinions expressed and makes it known that they are "those of the author and do not necessarily reflect the official policy or position of DFS or any other member, agency, organization, employer or company."  Big Grin


Users browsing this thread: