#71

Just Here for the Shaves
Williamsburg, KY
Today's Shave
[Image: 2kUzcgg.jpg]

Twhite, HighSpeed, godek and 2 others like this post
This post by Dave in KY mentions views and opinions expressed and makes it known that they are "those of the author and do not necessarily reflect the official policy or position of DFS or any other member, agency, organization, employer or company."  Big Grin
#72

Member
Burbank CA
Hello guys. I am the guy who made the TNNSER. I just joined. If you have any questions about it. I would be happy to try and answer the best I can.

Tom

FaceScraper, Rebus Knebus, HighSpeed and 3 others like this post
#73

Administrator
Philadelphia, PA
(06-15-2020, 07:10 PM)Twhite Wrote: Hello guys. I am the guy who made the TNNSER. I just joined. If you have any questions about it. I would be happy to try and answer the best I can.

Tom

thanks for joining and thanks for taking the time to design a 3d printed razor and sharing the design for free...

I tried one, but the top cap and base plate were so damn tight that it's basically stuck together, lol...

https://damnfineshave.com/thread-tnnser-...#pid313174
Tu ne cede malis, sed contra audentior ito.
#74

Member
Burbank CA
It takes a little bit of selective sanding. I have some pictures I can post tonight. How much you sand varies greatly. It depends on layout orientation layer lines ( resolution) of printer. 

I will try to give a more detailed explanation tonight when I post you some pictures. 

Tom

godek, JoeLr, andrewjs18 and 1 others like this post
#75

Administrator
Philadelphia, PA
(06-15-2020, 07:28 PM)Twhite Wrote: It takes a little bit of selective sanding. I have some pictures I can post tonight. How much you sand varies greatly. It depends on layout orientation layer lines ( resolution) of printer. 

I will try to give a more detailed explanation tonight when I post you some pictures. 

Tom

any consideration of printing and selling them assembled? I may consider buying just the top cap and base plate, if so..
Tu ne cede malis, sed contra audentior ito.
#76

Member
Burbank CA
No need plans on doing that. I was able to get a couple printed at work. I am really not allowed to do that.

The cap needs to be built standing up like this. 
[Image: 7-F2-F4-F00-1-D12-4938-B69-F-D699-D2457-F08.jpg]

Dave in KY, godek and ExtraProtein like this post
#77

Member
Burbank CA
[Image: 1-DC59-E95-8-DAB-4-F0-C-BED4-2-CC991195-F39.jpg]

The above image is where I start. I use a nail file, sapphire. As it cuts fast and leaves a nice finish. 
I first just file so that all layer lines are gone. I do the same to the underside of the tongue. You may have to go back and take a bit more after all other steps listed.
[Image: 4-A42-C3-A8-8-DFC-4731-AED6-7-E0-D192-BC9-EF.jpg]
Next step and the one you need to take care in doing. You need to blend the transition between the taper and the flat section. See where my knife is pointing. I use a small pen knife blade. Anything will work. Make sure you get underneath the flange areas. What this does is creates a better taper for the blade to follow when putting the cap on. 
[Image: 0-C9-B2154-BEA1-4-D58-8862-DF0-B09-E35-E55.jpg]
I then move my attention to the base. As you see I have the handle mounted. Speaking of mounting the handle. Most of you in the U.S. have come to find out that sourcing the hardware is next to impossible. I ended up having to buy 50 of each the metric flat head and jam nut from McMaster Carr. I have plenty now if you live in the US PM me we can work out shipping you some. 
Back to the filing. Do the same thing as you did to the cap. File the layer lines and bumps down only to be smooth. Now is the time for a dry fit. You may have tinker a bit. You should be really close. 

All the above takes maybe 5 minutes. Once you have the cap fitting. This is important. It should not be a loose fit. Snug is much preferred. As the blade is held by the tight fit of the cap to the base. 

Now is the time to try it with a blade. Important that you use an old blade for this. When you slide the cap over the blade for the first time. You will shave a bit of material from the cap. This is normal from my experience.

Open cap install a new blade and enjoy your shave. 
I hope this clears up some things for you all. 

Tom

ischiapp, godek, andrewjs18 and 5 others like this post
#78

Just Here for the Shaves
Williamsburg, KY
Wednesday June 17, 2020
Razor: @uacowboy TNNSER Razor
Blade: Gem (?)
Brush: Smattayu TSC Legacy Brush
Soap: @CBLSoap.com Roasted Oatmeal Stout
Aftershave 1: Humphrey's Alcoholado Maravilla
Balm: @LNHC Elixir
Aftershave 2: Dragonsbeard Dragonsbeard SFS
Talc: Vintage Avon Clint
Fragrance: Penhaligon's Sartorial
[Image: Cri13Mk.jpg]

Gopneg, DeepSea, ischiapp and 4 others like this post
This post by Dave in KY mentions views and opinions expressed and makes it known that they are "those of the author and do not necessarily reflect the official policy or position of DFS or any other member, agency, organization, employer or company."  Big Grin
#79
Printing the topcap at 101% or 102% can also help.

HTH
godek

Twhite likes this post
#80
I made such a razor for myself. made grinding. but couldn't shave. the blade angle sticks out and cuts the skin. I tried to move the lid to avoid it, but it didn't wor[Image: 6b7613aea8d8t.jpg]k out.[Image: 482b4cb633c8t.jpg]


Users browsing this thread: 1 Guest(s)