#21
(02-02-2022, 02:31 AM)Patriot Wrote:
(02-02-2022, 02:00 AM)Marko Wrote:
(02-01-2022, 10:34 PM)jesseix Wrote: They definitely don't play nice in the sandbox!

Yeah, I roll them out every year or two to see if their disposition has improved.  Nope.

I’ve had somewhat the same experience with wives.  
Every 7 to 24 years I try again.
I have a tendency to become attached to the ones with difficult dispositions…
Even after some polishing?
Best comment of the day.

ExtraProtein, keto and jesseix like this post
#22

Member
Chicago Suburbs
A straight razor has to be "shave ready" for your face before it can give a great shave. That means something different for every beard and face. Many razors that claim to be "shave ready" are not, especially if you have a tough beard.

Using a straight razor requires a variety of skills that can only be mastered over time. Nobody loves using a straight razor the first few times they use one.

ExtraProtein likes this post
#23
Still not interested in a straight.
#24
I’ve found out in my side by side one pass comparisons using two razors that of any razor in my den the Ikon Tek is hard to beat as far as efficiency and effective beard reduction. An especially at the price which is around $35. My Wolfman 1.55, Charcoal Goods Level 3 OC are close, but their price is significantly more expensive than the Ikon. The one that matches the Ikon and I say that after more recently doing a side by side is the 2011 Muhle R41. They are hard to find and usually very expensive if you do. In fact there’s only one on eBay right now that’s outrageously expensive. I don’t use mine very often because it made of Zamak and I’m not sure how well the finish would last if used a lot over time. Lastly the only razor that surpassed the Ikon Tek in the one pass side by side comparison and did it by a good margin was the 2021 Rocnel Sailor on setting 10. I’m sure it would have matched the Ikon on a setting somewhere between 7 to 9 but never had the chance to try those settings as I sold it thinking that a Ti version was coming out which I’m still hopeful about as it would probably be the perfect razor for me replacing many razors in my den because of the many settings as it can go from mild to very wild like no other razor I’ve used.

I have a lot of shave time with my Ikon Tek and have the head on a Tiban Ti handle that to me gives it better balance and maneuverability than the stock handle. I use aggressive skin stretching very similar to what you’d use if using a straight razor with 0 pressure.

So to me it’s a great razor at a bargain price but it does require sone taming.

Just my thoughts so may or may not be of any help to you.

Good hunting!

ExtraProtein, Deus Vult, zaclikestoshave and 1 others like this post
#25
(02-04-2022, 07:09 AM)Dragonsbeard Wrote: the 2011 Muhle R41. . . . I don’t use mine very often because it made of Zamak and I’m not sure how well the finish would last if used a lot over time.
Not to derail the thread, but I am curious: Is there a difference in the R41 2011 & 2013 topcaps? The screw would be the weakest point and most susceptible to decay (as I experienced with a 2013 and a losing encounter with gravity between shelf and floor). The cap alone is inexpensive to replace.

BJP likes this post
#26
(This post was last modified: 02-04-2022, 06:24 PM by Dragonsbeard.)
(02-04-2022, 04:47 PM)ewk Wrote:
(02-04-2022, 07:09 AM)Dragonsbeard Wrote: the 2011 Muhle R41. . . .  I don’t use mine very often because it made of Zamak and I’m not sure how well the finish would last if used a lot over time.
Not to derail the thread, but I am curious: Is there a difference in the R41 2011 & 2013 topcaps? The screw would be the weakest point and most susceptible to decay (as I experienced with a 2013 and a losing encounter with gravity between shelf and floor). The cap alone is inexpensive to replace.

Sorry about the 2013 drop damage. The way you can tell the difference between the two is the 2011 has a lower profile head and the scallops/combs are set differently. There is a site that sells 3D printed Top caps that are supposed to make the 2013 as efficient as the 2011 but I haven’t used one to verify that. I’ve not experienced any decay on my 2013 and I’ve had it and used it quite a bit throughout the years knowing it would be an easy replacement but not so with the 2011.

ewk likes this post
#27

Member
Chicago Suburbs
Since you are not interested in straight razors, perhaps you might be more inclined to try a DEvette. That is a DE razor that had had the safety bar removed. If you are looking for a DE razor with a big gap, that fits the bill. If you won't try that either then perhaps you do not really like big gaps after all.

https://www.youtube.com/watch?v=TJHwvctGShM


Users browsing this thread: 2 Guest(s)